To manage the remote SonicWALL through the VPN tunnel, select HTTP, HTTPS, or both from Management via this SA. Select HTTP, SSH, HTTPS, or any combination of the three in the User login via this SA to allow users to login using the SA. •
Also, are you having one or two VPNs with failover? Since you are seeing the packets being consumed, just check the statistics on the SA itself and see if the transmitted packets are bytes are increasing. If yes, then the SonicWall is forwarding the traffic correctly. Hi All, I'm still getting the hang of SonicWall personally and I need to setup failover for a site to site VPN we have going. I noticed there is a secondary IP address section for VPNs in the config, is it really as simple as the secondary IP being used if the primary goes down? Oops! We ran into a problem with your browser settings. To continue with us, please follow the below steps: From Safari Menu, click Preferences-> Privacy-> Cookies So I might have put in a wrong cert into sonicwall and now I can't even get into the console login page. Getting ERR_BAD_SSL_CLIENT_AUTH_CERT and when I open the invalid cert its self signed by sonicwall and pointing at .168 while my console ip is .1. Kind of stuck right now because I can't get back into the console to remove the bad cert.
Hi all, Just got a new client that has 2 SonicWalls. One in location A, one in location B with a site to site VPN configured. I recently got failover Internet installed at both locations and was hoping to get the site to site VPN configured to use the failover line if the main line fails.
On the Network| WAN Failover & Load Balancing page, under WAN Interface Monitoring, check the Enable Probe Monitoring box. Check the Respond to Probes box to have the SonicWall respond to TCP probes received on its WAN ports. Check the Any TCP-SYN to Port box to respond to TCP probes to the specified port number without validating them.
For small business, retail and branch office locations, the SonicWall TZ400 series delivers enterprise-grade protection. Flexible wireless deployment is available with optional 802.11ac dual-band wireless integrated into the firewall. SonicWall TZ300 series The SonicWall TZ300 series offers an all-in-one solution that protects networks from attack.
You'd have to make sure that the remote side VPN tunnel has both the primary WAN IP or DNS name and the secondary LTE IP or DNS name. If it loses connectivity to the primary IP it will attempt to connect to the VPN using the secondary IP. You should also be able to have it fall back to the primary once it comes back up. level 1 Idk, I never got 4g sticks to work, we used a cradlepoint instead on the sonicwall. It worked actually pretty good, however for those we did use it, they have no VPN, just a failover line for regular internet. I assume in the worst case that the VPN drops on failover, in the best it'll be fine. Probe responder.global.sonicwall.com on all interfaces in this group —Enable this checkbox to automatically set Logical/Probe Monitoring on all interfaces in the Group. . When enabled, this sends TCP probe packets to the global SNWL host that responds to SNWL TCP packets, responder.global.sonicwall.com, using a target probe destination address of 204.212.170.23:500 The VPN Policy window is displayed , Click the Advanced tab . Select the VPN bound to option. Select Interface X2 (3.3.3.3) as the Primary gateway as Site B is set as the same IP – 3.3.3.3. NOTE: By default, VPN policy bound to option is set to zone WAN where VPN tunnel will be established with Primary WAN as configured in Failover/Load balancing . For a SonicWALL appliance with a WWAN interface, such as a TZ 190, you can configure failover using the WWAN interface. Failover between the Ethernet WAN (the WAN port, OPT port, or both) and the WWAN is supported through the WAN Connection Model setting. On the Network| WAN Failover & Load Balancing page, under WAN Interface Monitoring, check the Enable Probe Monitoring box. Check the Respond to Probes box to have the SonicWall respond to TCP probes received on its WAN ports. Check the Any TCP-SYN to Port box to respond to TCP probes to the specified port number without validating them.